We test and review fitness products based on an independent, multi-point methodology. If you use our links to purchase something, we may earn a commission. Read our disclosures.
A weightlifting platform is a must for any garage gym. It protects your equipment and, more importantly, your home. Here’s how you can build a DIY weightlifting platform that can also have a squat rack attached.
A weightlifting platform is something that is not needed. It takes up a lot of space, is very heavy, and can be somewhat costly.
However, if you are practicing the olympic lifts I say without a doubt that it is an essential piece to your garage gym.
I see it being similar to using a bearing barbell. If you’ve never used one, you don’t know what you’re missing. However, once you feel the soles of your weightlifting shoes pound onto the wooden platform during a split jerk, you can’t go back.
Also, it deadens the sound of the barbell which is good for your neighbors or sleeping children. So I decided to make one of my own, and it’s been a wonderful addition to my garage.
Supplies
- 4 4’x8′ 3/4″ Pieces of Cheap Plywood
- 1 4’x8′ 3/4″ Piece of Quality Plywood (A/B or A/C, tell a worker at the hardware store and they’ll know what you’re talking about)
- 1 4’x8′ 3/4″ Stall Mat (I purchased mine from Tractor Supply)
- 3-4 Tubes of Heavy Duty Liquid Nails
- Box of 1.25″ Wood Screws
Tools
Total Cost: Approximately ~$150
Instructions
- Lay down 2 of your cheap 4’x8′ plywood sheets.
- Squeeze 1 full can of Liquid Nails making sure to get the corners.
- Lay down 2 more of your cheap 4’x8′ plywood sheets perpendicular to the other two you laid down previously.
- Screw sheets along edges about 2″ from the edge and down the middle,every 15″.
- Cut 4’x8′ stall mat in half using a xacto knife.
- Squeeze 1 full can of Liquid Nails on sides where the stall mats will be placed and lay down stall mats.
- Measure width of the base of the squat stand and cut the nice plywood allowing the squat stand to be bolted.
- Squeeze 1 full can of Liquid Nails where the nice piece of plywood will be laid.
- Lay the plywood and but put weight plates all over platform allowing it to seal overnight.
- Next morning: Bolt squat stand to platform using L Brackets, nuts, bolts, and lag bolts.
- Train.
Final Thoughts
Bolting the squat stand to the weightlifting platform allows you to feel secure when using any squat racks, as well as allowing kipping pullups and any other dynamic movement used in the rack. I bolted a Rogue SML-2 Squat Stand to the platform and that review can be found below.
All in all the weightlifting platform is something that is a great addition to any garage gym, but I would say if you aren’t worried about noise and don’t olympic lift than it isn’t very important.
Check out the review of the Rogue SML-2 Squat Stand that I attached to the platform here: Rogue SML-2 Squat Stand Review
Further reading
The Rogue Dumbbell Bumper Platesare a cool innovation for strength training. As with anything made by Rogue Fitness, they are very well done and can be just as effective in training. If you do a lot of dynamic dumbbell work and want to easily interchange weight, these are a great option. However, they are not designed to be dropped overhead. Read more
Does protein powder cause acne? Learn the truth about the relationship between protein supplements and skin health, plus natural alternatives to try. Read more
We asked a certified strength and conditioning coach to build a beginner core workout with the best core exercises to boost strength and sculpt your abs. Read more
Wondering how to train for mountain biking, rock climbing, backpacking, or kayaking? Here's how to set up your home gym for outdoor training. Read more